Configuring ADVPN in FortiOS 5.4 (Expert)

1. Configure the Hub FortiGate

Using the CLI, configure phase 1 parameters.

The auto-discovery commands enable the sending and receiving of shortcut messages to spokes (the hub is responsible for lettings the spokes know that they should establish those tunnels).

Note: aggressive mode is not supported currently for ADVPN.

config vpn ipsec phase1-interface
    edit "ADVPN"
        set type dynamic
        set interface "wan1"
        set proposal aes128-sha1
        set add-route disable
        set dhgrp 2
        set auto-discovery-sender enable
        set psksecret fortinet
    next
end

Configure the phase2 parameters.

This is a standard phase 2 configuration.

config vpn ipsec phase2-interface
    edit "ADVPN-P2"
        set phase1name "ADVPN"
        set proposal aes128-sha1
    next
end

Configure the tunnel interface IP.

ADVPN requires that tunnel IPs be configured on each device connecting to the topology. Those IP addresses need to be unique for each peer. A particularity of the hub is that it needs to define a bogus remote-IP address (10.10.10.254 in our example). This address should be unused in the topology and it will not be actually considered as part of the configuration for the hub.

config system interface
    edit "ADVPN"
        set vdom "root"
        set ip 10.10.10.1 255.255.255.255
        set type tunnel
        set remote-ip 10.10.10.254
        set interface "wan1"
    next
end

 Configure iBGP and route-reflection.

iBGP will be our overlay protocol of choice for enabling ADVPN communications. We are using an arbitrary private AS number (65000) in our example, and configuring a dynamic client group to reduce provisioning requirements.

While we are advertising our LAN network directly (“config network” command), route redistribution is a perfectly valid alternative.

config router bgp
    set as 65000
    set router-id 10.10.10.1
    config neighbor-group
        edit "ADVPN-PEERS"
            set remote-as 65000
            set route-reflector-client enable
        next
    end
    config neighbor-range
        edit 1
            set prefix 10.10.10.0 255.255.255.0
            set neighbor-group "ADVPN-PEERS"
        next
    end
    config network
        edit 1
            set prefix 192.168.1.0 255.255.255.0
        next
    end
end

Configure basic policies to allow traffic to flow between the local network and the ADVPN VPN topology. As we generally desire traffic to be allowed between spokes in an ADVPN setup, we must remember to create a policy allowing spoke to spoke communications.

config firewall policy
    edit 0
        set name "OUT ADVPN"
        set srcintf "lan"
        set dstintf "ADVPN"
        set srcaddr "all"
        set dstaddr "all"
        set action accept
        set schedule "always"
        set service "ALL"
        set status enable
    next
    edit 0
        set name "IN ADVPN"
        set srcintf "ADVPN"
        set dstintf "lan"
        set srcaddr "all"
        set dstaddr "all"
        set action accept
        set schedule "always"
        set service "ALL"
        set status enable
    next
    edit 0
        set name "ADVPNtoADVPN"
        set srcintf "ADVPN"
        set dstintf "ADVPN"
        set srcaddr "all"
        set dstaddr "all"
        set action accept
        set schedule "always"
        set service "ALL"
        set status enable
    next
end

2. Configure the Spoke FortiGates

Using the CLI, configure phase 1 parameters.

Note that we are configuring only one of the spokes in this example – the parameters that need to change for each spoke are highlighted in red.

config vpn ipsec phase1-interface
 edit "ADVPN"
  set interface "wan1"
  set proposal aes128-sha1
  set add-route disable
  set dhgrp 2
  set auto-discovery-receiver enable
  set remote-gw 10.1.1.1
  set psksecret fortinet
 next
end

Configure the phase2 parameters.

config vpn ipsec phase2-interface
    edit "ADVPN-P2"
        set phase1name "ADVPN"
        set proposal aes128-sha1
	set auto-negotiate enable
    next
end

 Configure the tunnel interface IP.

Notice that on the spokes, the remote IP is actually used and points to the IP defined on the hub.

config system interface
    edit "ADVPN"
        set vdom "root"
        set ip 10.10.10.2 255.255.255.255
        set type tunnel
        set remote-ip 10.10.10.1
        set interface "wan1"
    next
end

Config iBGP.

This is a static standard configuration and as stated for the hub, redistribution could be used instead of explicit route advertisement.

config router bgp
    set as 65000
    set router-id 10.10.10.2
    config neighbor
        edit "10.10.10.1"
            set soft-reconfiguration enable
            set remote-as 65000
        next
    end
    config network
        edit 1
            set prefix 192.168.2.0 255.255.255.0
        next
    end
end

Configure a static route for the tunnel IP subnet.

This is an important special step for the spokes as they need a summary route that identifies all tunnel IP used over your topology to point towards the ADVPN interface. In our example, we use 10.10.10.0/24 (if our network planning expects less than 255 sites). Be sure to adequately plan this IP range as it needs to be hardcoded in the spokes.

config router static
    edit 3
        set dst 10.10.10.0 255.255.255.0
        set device "ADVPN"
    next
end

Configure policies.

config firewall policy
    edit 0
        set name "OUT ADVPN"
        set srcintf "lan"
        set dstintf "ADVPN"
        set srcaddr "all"
        set dstaddr "all"
        set action accept
        set schedule "always"
        set service "ALL"
        set status enable
    next
    edit 0
        set name "IN ADVPN"
        set srcintf "ADVPN"
        set dstintf "lan"
        set srcaddr "all"
        set dstaddr "all"
        set action accept
        set schedule "always"
        set service "ALL"
        set status enable
    next
end

Results

We can validate the behaviour of our configuration using a few commands. We are going to run these commands from SPOKE A.

get router info routing-table bgp will at a minimum display the learned routes from the topology. Note the recursive routing – a result of our spoke’s required static route. In this case, there has not been any traffic between our local subnet (192.168.2.0/24) and the other spoke’s subnet, as the routes are both going through the hub.

B       192.168.1.0/24 [200/0] via 10.0.0.1, ADVPN, 22:30:21
B       192.168.3.0/24 [200/0] via 10.0.0.3 (recursive via 10.0.0.1), 22:30:21

However once we initiate a ping between both spokes, we obtain a different display of routing information – routing now goes through a newly established dynamic tunnel directly through the remote spoke rather than through the hub. The ping hiccup that occurs is the tunnel rerouting through a newly negotiated tunnel to the other spoke.

Our routing information now displays the remote subnet as being available through the spoke directly, through interface ADVPN_0, a dynamically instantiated interface going to that spoke.

FG # exec ping-options source 192.168.2.1

FG # exec ping 192.168.3.1
PING 192.168.3.1 (192.168.3.1): 56 data bytes
64 bytes from 192.168.3.1: icmp_seq=0 ttl=254 time=38.3 ms
64 bytes from 192.168.3.1: icmp_seq=1 ttl=254 time=32.6 ms
Warning: Got ICMP 3 (Destination Unreachable)
64 bytes from 192.168.3.1: icmp_seq=2 ttl=255 time=43.0 ms
64 bytes from 192.168.3.1: icmp_seq=3 ttl=255 time=31.7 ms
64 bytes from 192.168.3.1: icmp_seq=4 ttl=255 time=31.2 ms

--- 192.168.3.1 ping statistics ---
5 packets transmitted, 5 packets received, 0% packet loss
round-trip min/avg/max = 31.2/35.3/43.0 ms

FG # get router info routing-table bgp 

B       192.168.1.0/24 [200/0] via 10.0.0.1, ADVPN, 22:34:13
B       192.168.3.0/24 [200/0] via 10.0.0.3, ADVPN_0, 00:02:28

FG # diag vpn tunnel list
list all ipsec tunnel in vd 0
------------------------------------------------------
name=ADVPN_0 ver=1 serial=a 10.1.1.2:0->10.1.1.3:0
bound_if=6 lgwy=static/1 tun=intf/0 mode=dial_inst/3 encap=none/0
 parent=ADVPN index=0
proxyid_num=1 child_num=0 refcnt=19 ilast=3 olast=604 auto-discovery=2
stat: rxp=7 txp=7 rxb=1064 txb=588
dpd: mode=on-demand on=1 idle=20000ms retry=3 count=0 seqno=0
natt: mode=none draft=0 interval=0 remote_port=0
proxyid=ADVPN-P2 proto=0 sa=1 ref=2 serial=1 auto-negotiate adr
  src: 0:0.0.0.0/0.0.0.0:0
  dst: 0:0.0.0.0/0.0.0.0:0
  SA: ref=3 options=2f type=00 soft=0 mtu=1438 expire=42680/0B replaywin=2048 seqno=8 esn=0
  life: type=01 bytes=0/0 timeout=43152/43200
  dec: spi=9a487db3 esp=aes key=16 55e53d9fbc8dbeaa6df1032fbc80c4f6
       ah=sha1 key=20 a1470452c6a444f26a070add087f0d970c18e3a7
  enc: spi=3c37fea7 esp=aes key=16 8fd62a6745a9ba4fda062d4504b76851
       ah=sha1 key=20 44c606f1ef1bf5739ba62f6572031aa956974d0a
  dec:pkts/bytes=7/588, enc:pkts/bytes=7/1064
------------------------------------------------------
name=ADVPN ver=1 serial=9 10.1.1.2:0->10.1.1.1:0
bound_if=6 lgwy=static/1 tun=intf/0 mode=auto/1 encap=none/0
proxyid_num=1 child_num=1 refcnt=22 ilast=8 olast=8 auto-discovery=2
stat: rxp=3120 txp=3120 rxb=399536 txb=191970
dpd: mode=on-demand on=1 idle=20000ms retry=3 count=0 seqno=12
natt: mode=none draft=0 interval=0 remote_port=0
proxyid=ADVPN-P2 proto=0 sa=1 ref=2 serial=1 auto-negotiate adr
  src: 0:0.0.0.0/0.0.0.0:0
  dst: 0:0.0.0.0/0.0.0.0:0
  SA: ref=3 options=2f type=00 soft=0 mtu=1438 expire=4833/0B replaywin=2048 seqno=5ba esn=0
  life: type=01 bytes=0/0 timeout=43148/43200
  dec: spi=9a487db2 esp=aes key=16 4f70d27edad656cfcacbae61b23d4b11
       ah=sha1 key=20 b19ea87c90dd92d1cab58cbf24ae8fe12ee927cb
  enc: spi=b3dde355 esp=aes key=16 efbb4440df75018610b4ba8f5756167d
       ah=sha1 key=20 81cc9cee3bee1c2dba0eb1e7ac66e9d34b67bde9
  dec:pkts/bytes=1465/90152, enc:pkts/bytes=1465/187560
------------------------------------------------------