IMPORTANT NOTE: The device must be professionally installed.

The device can be mounted either outdoors or indoors and may be attached to either a pole or wall.

Note: The included PoE injector must be mounted indoors, as it is not weatherproof.

To mount the device on a wall

1. Insert the mounting anchors into an appropriate wall.
2. Screw the mounting screws into the anchors, ensuring that enough of the screw is exposed to allow for mounting the device.
3. Hang the device onto the mounting screws, then slide the unit downwards to secure it into place.
   

To mount the FortiAP unit on a pole

1. Loop the provided pole straps through the slots on the back of the device, then
   around the pole.
2. Tighten the straps to ensure that the device is firmly in place.
   

The post FortiAP 112D Installation Guide appeared first on Fortinet Cookbook.

To use the table top stand

1. Orient the device to face the wireless router or AP.
2. Select either 8° and 23° tilting angles.
3. Connect the LAN cable under the table stand to the DC injector.

To mount the device to a pole

1. Orient the device to face the wireless router or AP.
2. Loop the provided two cable ties through the slots on the back of the device and then around the pole.
3. Tighten the strap and ensure the device is firmly in place.

To mount the device to a wall

1. Using the wall mount base as a template, mark the location of the mounting holes on a flat wall surface.
2. Drill the mounting holes in the marked locations. The holes are 60mm (2.3 inches) apart.
3. Fasten the unit securely to the wall using the provided mounting anchors and screws.
   

The post FortiAP L212B 215B Installation Guide appeared first on Fortinet Cookbook.

Using the provided hardware, the FortiAP unit can be mounted on a wall.

To mount the unit on a wall:

1. Select an appropriate location and mark the location on the wall where the anchors will be located.
2. Insert the anchors provided in the wall mount kit into the wall in the marked locations. If necessary, drill holes into the wall with an appropriately sized drill bit prior to inserting the anchors.
3. Screw the provided M3x16L screws into the two anchors, leaving enough of the screws exposed to ensure that the unit can be mounted on them.
4. Mount the FortiAP unit onto the screws and ensure that it is mounted securely.
   You can now proceed with connecting your FortiAP unit.
   

The post FortiAP 14C Installation Guide appeared first on Fortinet Cookbook.

The unit can be mounted on a wall or ceiling using the provided wall-mount hardware. It can also be mounted on any appropriate magnetic surface, such as the side of a desk, using the built-in magnets on the bottom of the device.

The device can be mounted horizontally or vertically as needed.

To mount the device using the magnets

1. Select an appropriate location, such as a shelf or office partition, onto which the device can be stuck.
2. Stick the device to the magnetic material and ensure that it is mounted securely.
   

To mount the device on a wall or ceiling

1. Select an appropriate location, then mark the location on the wall or ceiling where the anchors will be located.
2. Drill the mounting holes in the marked locations with an appropriately sized drill bit, then insert the provided anchors into the holes.
3. Screw the provided screws into the anchors, leaving enough of the screw exposed to ensure that the unit can be mounted on them.
4. Mount the device onto the screws and ensure that it is mounted securely.
   

The post FortiAP 25D Installation Guide appeared first on Fortinet Cookbook.

Using the provided hardware, the FortiAP unit can be attached to a ceiling or wall.

To attach the unit to a wall or ceiling:

1. Select an appropriate location and, using the mounting template included in this guide, mark the location on the wall or ceiling where the anchors will be located.
2. Screw the provided anchors into the wall or ceiling in the marked locations. If necessary, drill holes into the wall or ceiling with an appropriately sized drill bit prior to inserting the anchors.
3. Screw the provided P3.5×32 screws into the two anchors, leaving enough of the screws exposed to ensure that the unit can be mounted on them.
4. Mount the FortiAP unit onto the screws and ensure that it is mounted securely.
5. Use the Kensington security slot to attach a cable lock (cable lock is not included) to protect your FortiAP device from unauthorized removal. You can now proceed with connecting your FortiAP unit.
   

To attach the unit to a ceiling using the provided T-rail connectors:

1. Attach the T-rail connectors to the bottom cover of the FortiAP unit using the provided P2.6×10 screws.
   Two sizes of T-rail connectors are included in the mounting hardware kit: 15/16in (2.38cm) and 9/16in (1.43cm).
   If extra space is required to accommodate drop ceiling tiles, use the provided spacers and P2.6×25 screws.
   
2. Line up the connected T-rail connectors with an appropriately sized rail and press the unit onto the rail until it snaps into place.
   
3. Use the Kensington security slot to attach a cable lock (cable lock is not included) to protect your FortiAP device.
   You can now proceed with connecting your FortiAP unit.

The post FortiAP 28C Installation Guide appeared first on Fortinet Cookbook.

IMPORTANT NOTE: The device must be professionally installed and must use the supplied antennas.

The unit is designed for outdoor use and may be attached to either a pole or wall.

Note: The device can be mounted either outdoors or indoors. The included PoE injector must be mounted indoors, as it is not weatherproof.

Antennas

The FortiAP 224D unit provides dual concurrent radio signals. Use the 2.4GHz
antenna mounts to access 802.11b/g/n signals, and the 5GHz antenna mounts
to access 802.11a/n signals. To use both radio frequencies concurrently, use all four WiFi antennas.

To Install the WiFi antennas

1. Insert the antenna base firmly into the appropriate antenna mount.
2. Securely hand tighten the fastening collar.
3. Repeat for the remaining antennas.

Cabling

The unit requires 48V DC power, which is delivered by the PoE injector, over a straight-through Ethernet cable.

To install the cable

1. Thread the RJ-45 plug through the coupling ring, sealing gland, and panel connector, then insert it into the PoE port on the unit.
2. Screw the panel connector onto the back of the device, being careful not to pinch the Ethernet cable.
3. Slide the sealing gland along the cable into panel connector.
4. Thread the coupling ring onto the panel connector and tighten it until the sealing gland is compressed, making a watertight seal on the cable.
   

Mounting

The unit is designed for outdoor use and may be attached to either a pole or wall.

To mount the device on a wall

1. nsert the mounting anchors into an appropriate wall.
2. Screw the mounting screws into the anchors, ensuring that enough of the
   screw is exposed to allow for mounting the device.
3. Place the device onto the mounting screws, then slide the unit downwards to lock it into place.

To mount the FortiAP unit on a pole

1. Loop the provided pole straps through the slots on the back of the device, then around the pole.
2. Tighten the strap with an appropriate screw driver and ensure that the device is firmly in place.

The post FortiAP 224D Installation Guide appeared first on Fortinet Cookbook.

The unit can be mounted on a wall or ceiling using the provided wall/ceiling mounting kit, or to an appropriate ceiling using the T-rail mounting kit.

To attach the unit to a T-rail

1. Attach the T-rail clips to the bottom of the unit using two P2.6X12 screws.
   If extra space is required to accommodate drop ceiling tiles, use the provided spacers and P2.6×25 screws.
2. Attach the provided antennas to the device.
3. Line up the connected T-rail clips with an appropriately sized rail, then press the unit into the rail until it snaps into place.

Note: Two sizes of T-rail clips are included: 2.38cm (15/16in) and 1.43cm (9/16in).

To protect your device from unauthorized removal, use the Kensington™ Security Slot to attach a cable lock (not included).

To attach the unit to a wall or ceiling

1. Select an appropriate location, then mark the locations on the wall or ceiling where the anchors will be inserted.
2. Drill the mounting holes, then insert the anchors into the holes.
3. Attach the mounting bracket to the anchors using two P3.5×34 screws.
4. Insert two P2.6X12 screws into the bottom of the unit, leaving enough of the screws exposed so that the unit can be mounted to the mounting bracket.
   If extra space is required between the unit and the mounting bracket, use the spacers and P2.6×25 screws from the T-rail mounting kit.
5. Attach the provided antennas to the device, then mount the device on the installed mounting bracket and rotate it clockwise to secure it in place.
   

The post FortiAP S313C/S323C Installation Guide appeared first on Fortinet Cookbook.

The unit can be mounted on a desk or on a wall or ceiling using the provided wall/ceiling mounting hardware kit.

FortiAP C225C and FortiAP C225SC have external antennas. Attach the antennas to the antenna mounts before you install the unit to a wall or ceiling.

Note: FortiAP C220C and FortiAP C220SC have internal antennas. This step is not applicable when installing those models.

To attach the unit to a wall

Before you begin: Select an appropriate location. Mark the locations on the wall where the anchors will be inserted, and then drill the mounting holes.

1. Insert the anchors into the mounting holes.
2. Use the screws to attach the mounting bracket to the anchors.
3. Mount the device on the mounting bracket, then slide it to the left until it clicks into place.
   

To attach the unit to a ceiling tile

Before you begin: Remove the ceiling tile from its track. Mark the location on the ceiling tile where the screws will be inserted, and then drill the holes.

1. Use the screws, washers, and wing nuts to attach the mounting bracket to the celing tile.
2. Mount the device on the mounting bracket, then slide it to the left until it clicks into place.
3. Install the ceiling tile into its track.
   

The post FortiAP C220C, C225C, C220SC, C225SC Installation Guide appeared first on Fortinet Cookbook.

The unit can be mounted on a wall or ceiling using the provided wall/ceiling mounting hardware kit, and to an appropriate ceiling using the T-rail mounting hardware kit.

To attach the unit to a wall or ceiling

1. Select an appropriate location, then mark the locations on the wall or ceiling where the anchors will be inserted.
2. Drill the mounting holes, then insert the anchors into the holes.
3. Attach the mounting bracket to the anchors using two P3.5×32 screws.
4. Insert two P2.6X12 screws into the bottom of the unit, leaving enough of the screws exposed so that the unit can be mounted to the mounting bracket. If extra space is required between the unit and the mounting bracket, use the spacers and P2.6×25 screws from the T-rail mounting hardware kit.
5. Mount the device on the mounted mounting bracket then rotate it clockwise to secure it in place.

To attach the unit to a T-rail

1. Attach the T-rail clips to the bottom of the unit using two P2.6X10 screws. If extra space is required to accommodate drop ceiling tiles, use the provided spacers and P2.6×25 screws.
        
   Note: Two sizes of T-rail clips are included in the mounting kit: 2.38cm (15/16in) and 1.43cm (9/16in).
2. Line up the connected T-rail clips with an appropriately sized rail, then press the unit into the rail until it snaps into place.
   
   Note: To protect your device from unauthorized removal, use the Kensington Security Slot to attach a cable lock (not included).

The post FortiAP 223C Installation Guide appeared first on Fortinet Cookbook.

Using the provided hardware, the FortiAP unit can be attached to a ceiling or wall.

To attach the unit to a ceiling or wall using the mounting bracket:

1. Attach the mounting bracket to the wall or ceiling using the mounting template and the provided wall/ceiling mounting hardware kit.
2. Insert the provided short screws into the bottom cover of the FortiAP unit.
3. Leave enough of the screws exposed to ensure that the unit can be attached to the mounting bracket.
   If extra space is required, use the provided spacers and long screws from the T-Rail mounting hardware kit to increase the space between the unit and the mounting bracket.
4. Mount the FortiAP unit on the mounting bracket by rotating the unit clockwise about 90 degrees to secure it in place.
   

To attach the unit to a ceiling using the provided T-rail connectors:

1. Attach the T-rail connectors to the bottom cover of the FortiAP unit using the provided short screws.
   Two sizes of T-rail connectors are included in the mounting hardware kit: 15/16in (2.38cm) and 9/16in (1.43cm).
   If extra space is required to accommodate drop ceiling tiles, use the provided spacers and long screws.
        
2. Line up the connected T-rail connectors with an appropriately sized rail and press the unit onto the rail until it snaps into place.
   
   Note: To protect your FortiAP unit, use the Kensington security slot to attach a
   cable lock (cable lock is not included).

The post FortiAP 223B Installation Guide appeared first on Fortinet Cookbook.

IMPORTANT NOTE: The device must be professionally installed.

The unit is designed for outdoor use and may be attached to a pole. A waterproof connector is supplied to ensure a watertight seal for connecting the Ethernet cable to the device.

Note: The device can be mounted either outdoors or indoors.

To mount the device on a pole with the tilt bracket

1. With tilt mount bracket key hole pointing down, thread two of the 1.25x110mm locking screws, flat washers, spring washers, and locking nuts on one side of the pole mount bracket and tilt mount bracket.
2. Mount the bracket to a pole at the desired height and thread the two remaining 1.25x110mm locking screws, flat washers, spring washers, and locking nuts. Tighten all four screws to its position.
3. Screw in four of the 1.25x12mm mounting screws through the tilt bracket to the back of the device to secure it to the pole.
4. To adjust the tilt, loosen the tilting screws located at the center of the tilting bracket. Tighten the screws back once the angle is fixed.

1. 1.25x110mm Locking Screw
2. Spring Washer
3. Flat Washer
4. Pole Mount Bracket
5. 1.25x12mm Mounting Screw
6. Tilt Bracket

The post FortiAP L822C Installation Guide appeared first on Fortinet Cookbook.

IMPORTANT NOTE: The device must be professionally installed and must use the supplied antennas.

The unit is designed for outdoor use and may be attached to either a pole or wall. A waterproof connector is supplied to ensure a watertight seal for connecting the Ethernet cable to the device.

Note: The device can be mounted either outdoors or indoors. The included PoE injector and surge protector must be mounted indoors, as they are not weatherproof.

To mount the device on a wall

1. Using the wall-mount base as a template, mark the location of the mounting bolt holes on a flat wall surface.
2. Drill the mounting holes in the marked locations.
3. Fasten the wall-mount base securely to the back of the unit using the provided mounting screws.
4. Attach the unit and base assembly to the wall using the provided mounting bolts.
   
5. Securely tighten the mounting bolts.
   

To mount the FortiAP unit on a pole

1. Fasten the wall-mount base securely to the back of the unit using the provided mounting screws.
2. Attach the pole-mount bracket to the wall-mount base using with the provided screws. The pole-mount bracket can be attached either vertically or horizontally, as required.
        
3. Loop the provided pole strap through the slots on the pole-mount bracket and then around the pole.
4. Tighten the strap with an appropriate screw driver and ensure that the device is firmly in place.
   

The post FortiAP S422E Installation Guide appeared first on Fortinet Cookbook.

IMPORTANT NOTE: The device must be professionally installed.

The unit is designed for outdoor use and may be attached to either a pole or wall. A waterproof connector is supplied to ensure a watertight seal for connecting the Ethernet cable to the device.

Note: The device can be mounted either outdoors or indoors. The included PoE injector and surge protector (not included) must be mounted indoors, as they are not weatherproof.

To mount the device on a wall

1. Using the wall-mount base as a template, mark the location of the holes on a flat wall surface.
2. Drill the mounting holes in the marked locations.
3. Attach the unit and base assembly to the wall using the provided plastic anchors and anchor screws.
4. Fasten the wall-mount base securely to the back of the unit using the provided M8 mounting screws.
   

To mount the device on a pole

1. Attach the pole-mount bracket securely to the back of the unit using the provided M8 mounting screws, spring washers, and flat washers.
2. Attach the pole-mount bracket using with the provided screws.
3. Loop the provided pole straps through the slots in the pole-mount bracket and then around the pole.
4. Tighten the pole straps with an appropriate screw driver and ensure that the device is firmly in place.
        

The post FortiAP L322C Installation Guide appeared first on Fortinet Cookbook.

Using the provided hardware, the FortiAP unit can be attached to a ceiling or wall.

To attach the unit to a wall using the wall mounting hardware kit:

1. Insert the anchors provided in the wall mounting hardware kit into an appropriate location on a wall.
2. Insert the screws provided in the wall mounting hardware kit into the
   anchors.
3. Mount the FortiAP unit onto the screws.

To attach the unit to a ceiling using the T-rail mounting hardware kit:

1. Attach the T-rail connector to the bottom cover of the FortiAP unit using
   the four provided short screws.
   If extra space is required to accommodate drop ceiling tiles, use the taller
   T-rail connector.
2. Line up the connected T-rail connector with an appropriately sized rail
   and twist the unit onto the rail until it snaps into place.

Note: To protect your FortiAP unit, use the Kensington security slot to
attach a cable lock (cable lock is not included).

The post FortiAP 320B Installation Guide appeared first on Fortinet Cookbook.

The unit can be mounted on a wall or ceiling using the provided wall/ceiling mounting kit, or to an appropriate ceiling using the T-rail mounting kit.

To attach the unit to a T-rail

1. Attach the T-rail clips to the bottom of the unit using two P2.6X10 screws.
   If extra space is required to accommodate drop ceiling tiles, use the provided spacers and P2.6×25 screws.
2. Line up the connected T-rail clips with an appropriately sized rail, then press the unit into the rail until it snaps into place.

Note: Two sizes of T-rail clips are included: 2.38cm (15/16in) and 1.43cm (9/16in).

To protect your device from unauthorized removal, use the Kensington™ Security Slot to attach a cable lock (not included).

To attach the unit to a wall or ceiling

1. Select an appropriate location, then mark the locations on the wall or ceiling where the anchors will be inserted.
2. Drill the mounting holes, then insert the anchors into the holes.
3. Attach the mounting bracket to the anchors using two P3.5×32 screws.
4. Insert two P2.6X15 screws into the bottom of the unit, leaving enough of the screws exposed so that the unit can be mounted to the mounting bracket.
   If extra space is required between the unit and the mounting bracket, use the spacers and P2.6×25 screws from the T-rail mounting kit.
5. Mount the device on the installed mounting bracket then rotate it clockwise to secure it in place.
   

The post FortiAP S321CR Installation Guide appeared first on Fortinet Cookbook.

IMPORTANT NOTE: The device must be professionally installed.

To mount the device on a wall

1. Using the wall-mount bracket as a template, mark the location of the six mounting bolt holes on a flat wall surface.
2. Drill the mounting holes in the marked locations.
3. Fasten the wall-mount bracket securely to the back of the unit using the provided P10x16 mounting screws and washers. Use P6x35, P6x20, and washers to connect the device to the wall.
   

To mount the FortiAP unit on a pole

1. Loop the provided pole strap through the slots in the pole-mount bracket then around the pole.
2. Tighten the strap with the appropriate screw driver and ensure the device is firmly in place.
3. Attach the device to the opposite side of the pole using with the provided P10x100 screws, locknuts, and washers. See the diagram.
   

The post FortiAP S322C Installation Guide appeared first on Fortinet Cookbook.

IMPORTANT NOTE: The device must be professionally installed and must use the supplied antennas.

The unit is designed for outdoor use and may be attached to either a pole or wall. A waterproof connector is supplied to ensure a watertight seal for connecting the Ethernet cable to the device.

Note: The device can be mounted either outdoors or indoors. The included PoE injector and surge protector must be mounted indoors, as they are not weatherproof.

To mount the device on a wall

1. Using the wall-mount base as a template, mark the location of the mounting bolt holes on a flat wall surface.
2. Drill the mounting holes in the marked locations.
3. Fasten the wall-mount base securely to the back of the unit using the provided mounting screws.
4. Attach the unit and base assembly to the wall using the provided mounting bolts.
   
5. Securely tighten the mounting bolts.
   

To mount the FortiAP unit on a pole

1. Fasten the wall-mount base securely to the back of the unit using the provided mounting screws.
2. Attach the pole-mount bracket to the wall-mount base using the provided screws.
   The pole-mount bracket can be attached either vertically or horizontally, as required.
   
3. Loop the provided pole strap through the slots on the pole-mount bracket and then around the pole.
4. Tighten the strap with an appropriate screw driver and ensure that the device is firmly in place.

The post FortiAP S322CR Installation Guide appeared first on Fortinet Cookbook.

Note: The FortiAntenna-M22 is suitable for poles one to four inches (approx 2.5-10 cm) in diameter.

1. Place item number 2 on the antenna, as illustrated in the above drawing.
   Align with the screw holes.
2. Connect item 2 to the antenna with spring washers (11), flat washer (10), and nuts (12).
3. Tighten the nuts at a torque of 30 in lbs (3.4 Nm).
   
4. Connect item 3 to item 2 ONLY, as illustrated in the above image, with items 6, 7, 8, and 13.
   Leave screw slightly loose.
5. Connect item 3 to item 5 as illustrated below, using items 6, 7, 8, and 13.
   Leave screw slightly loose.
   
6. Attach items 4 and 5 to the pole as illustrated below, then connect them using items 6, 7, and 9.
   
7. Adjust the desired angle, and fully tighten the loose screws from steps 4 & 5.
8. Tighten the nuts at a torque of 30 in lbs (3.4 Nm).

Wall Mounting

The post FortiAntenna-M22 Installation Guide appeared first on Fortinet Cookbook.

Using the provided hardware, the FortiAP unit can be attached to a wall or pole.

To attach the unit to a wall:

1. Setup the provided anchors and screws in the desired wall.
2. Hang the FortiAP device on the screws.
   

To attach the unit to a pole:

1. Loop the wire belts through the slots on the rear of the device and then around the pole.
2. Tighten the belts to ensure that the device is firmly in place.
   

Antenna direction

The FortiAP 112B has a directional antenna located on the front of the device. The strongest signal is achieved in the 60 degree range shown in the below image.

For a reliable wireless connection, the units to which you would like to connect should be within this range.

The post FortiAP 112B Installation Guide appeared first on Fortinet Cookbook.

The unit can be mounted on a wall or ceiling using the provided wall/ceiling mounting kit, and to an appropriate ceiling using the T-rail mounting kit.

To attach the unit to a T-rail

1. Attach the T-rail clips to the bottom of the unit using two P2.6X12 screws.
   If extra space is required to accommodate drop ceiling tiles, use the provided spacers and P2.6×25 screws.
2. Line up the connected T-rail clips with an appropriately sized rail, then press the unit into the rail until it snaps into place.

Note: Two sizes of T-rail clips are included: 2.38cm (15/16in) and 1.43cm (9/16in).

To protect your device from unauthorized removal, use the Kensington™ Security Slot to attach a cable lock (not included).

To attach the unit to a wall or ceiling

1. Select an appropriate location, then mark the locations on the wall or ceiling where the anchors will be inserted.
2. Drill the mounting holes, then insert the anchors into the holes.
3. Attach the mounting bracket to the anchors using two P3.5×34 screws.
4. Insert two P2.6X12 screws into the bottom of the unit, leaving enough of the screws exposed so that the unit can be mounted to the mounting bracket.
   If extra space is required between the unit and the mounting bracket, use the spacers and P2.6×25 screws from the T-rail mounting kit.
5. Mount the device on the installed mounting bracket and rotate it clockwise to secure it in place.
   

The post FortiAP S311C/S321C Installation Guide appeared first on Fortinet Cookbook.